VWEICYY 2PACK 4 AA Battery Holder housing with Leads (2PCS 4 x 1.5V, Without Cover)
Quick take
This 2-pack provides two separate holders for 4x 1.5V AA batteries, each with wire leads you can solder into a circuit. It is geared toward DIY repairs and projects where you need battery power brought out to the wiring, and it uses a stainless steel spring to keep cells in place for faster swaps. The main caveat is that it ships without a cover, and buyer feedback includes limited but serious safety concern in one review, so you should inspect connections and ensure the build is safe for your application.
Pros and cons
Pros
- Designed for 4x AA (1.5V) battery setups, sold as a 2-pack.
- Spring-based retention makes battery installation and replacement straightforward.
- Comes with 22AWG lead wire with tinned ends that are intended to be solder-friendly.
- Stated build material is tough ABS plastic, designed to resist cracking.
Cons
- No cover included, so you may need to add your own housing for protection and strain relief.
- Wire length is limited (about 5.7 in / 14.5 cm), which may not fit every enclosure.
- Buyer-review evidence is mixed, including a rare but serious safety-related report, so fit and wiring matter.
What buyers think
Overall buyer-review evidence leans positive for practical repair use, with comments that the holders match expectations, install correctly, and restore devices back to working order. Some buyers describe quick delivery and basic satisfaction, and a few mention they are working as intended after installation. Buyer-review evidence is too limited to establish a consistent pattern for performance details beyond “works for the intended purpose,” but there is at least one highly negative safety-related report, so it is reasonable to treat this as a “check before you commit” purchase and inspect how the holder is seated and how the leads are connected.
Key features that matter for buying
4x AA power with leads for wiring projects
These holders are built to take four AA cells and bring power out through included leads. That makes them a good fit when you are replacing a dead battery harness, rebuilding a small device, or wiring battery power into a custom enclosure.
Easy battery swaps, spring retention
A stainless steel spring is used to keep each AA in place. In day-to-day use, this generally translates to simpler insertion and replacement compared with holders that rely on more complex clips or covers.
Solder-friendly wire ends (22AWG, tinned)
The leads are listed as 22AWG, with tin-plated wire ends intended to be easy to solder. If your project requires soldering rather than quick-connect terminals, this feature can reduce friction during assembly.
No cover included
These battery cases are sold “without cover.” If your device needs a protected battery compartment, you will likely want to plan for an enclosure, a separate cap, or a way to shield the contacts and leads. This is also relevant for strain relief, since the leads may bear some tension if your build is not designed carefully.
Specifications at a glance
- Battery type: 4x 1.5V AA
- Pack size: 2 holders (2-pack)
- Lead wire: 22AWG, tinned ends, red and black wire
- Wire length: 5.7 in (14.5 cm)
- Case material: ABS plastic (tough, intended to resist cracking)
- Approximate dimensions (each holder): 2.75 in x 2.56 in x 0.75 in (7 cm x 6.5 cm x 1.9 cm)
- Battery holder type: with wire leads (USB-free in this listing), no cover
Pros and cons for different buyer types
Best for
- DIY repairs where an existing battery compartment needs a replacement battery harness.
- Small electronics builds where you need power brought out with solderable leads.
- Projects that can accommodate the listed size and wire length.
Who should be cautious or choose a different option
- If you need a fully enclosed battery compartment out of the box, you will likely prefer a holder that includes a cover.
- If your enclosure is tight, the listed dimensions and wire length may limit placement options.
- If your design is sensitive to contact stability and you cannot control how the battery sits and the leads are routed, double-check your installation approach before powering up.
Alternatives to consider (based on your priorities)
- Covered battery holders: If you want a ready-to-install, protected compartment, a covered 4x AA holder can reduce your need to source extra casing parts.
- Terminal-based harness options: If you do not solder, look for holders that use spade/quick-connect terminals so you can adapt without soldering.
- Different lead length: For longer runs inside larger enclosures, you may prefer holders with longer wires to avoid strain at the solder joints.
Verdict
The VWEICYY 2-pack 4x AA battery holder with leads is a practical choice for repairs and DIY projects that need solderable battery power wiring. The spring-based cell retention and ABS construction are aligned with straightforward assembly, but the “no cover” design means you should plan for protection and secure routing. Given that buyer feedback includes a rare safety-related report, treat this as a build where you inspect fit, routing, and connections carefully before leaving the project powered unattended.
FAQs
Does this battery holder come with a cover?
No. It is sold without a cover, so you may need to add your own enclosure or protective housing depending on your project.
What battery type does it support?
It supports four AA batteries, each rated at 1.5V.
Are the leads solderable?
Yes. The leads are listed as 22AWG with tinned (tin-plated) wire ends intended for soldering.
How long are the wires?
The wire length is listed as 5.7 inches (14.5 cm).
Is this suitable for replacing an old battery harness?
It can be, especially if your original setup used a 4x AA holder with leads. Measure your space, confirm the wire routing needs, and plan for a cover or protection if your device requires it.
Specifications
| Product Title | VWEICYY 2PACK 4 AA Battery Holder housing with Leads,2PCS 4 x 1.5V AA Battery Holder Case, Without Cover |
|---|---|
| Category | Electronics > Household Batteries, Chargers & Accessories > Battery Holders |
| Brand | VWEICYY |
| Manufacturer | VWEICYY |
| Model Number | VW4AAW-2 |
| Item Weight | 0.04 Kilograms |
| Warranty Description | 1 year |
| Voltage | 6 Volts |
| Reusability | Rechargeable |
| Unit Count | 2.0 Count |
| Item Dimensions | 2.4 x 2.3 x 0.6 inches |
| Antenna Location | Gaming Controller |
| Recommended Uses For Product | Gaming Controller |
Recommended next
DORHEA 12PCS 18650 Battery Holder Bundle with Wire 18650 Battery Holder Case (1/2/3/4 Slots)
This DORHEA 12-pack bundle includes 1-, 2-, 3-, and 4-cell 18650 holders (with preinstalled red and black leads) for DIY battery projects and replacements. It is a budget-friendly way to build common 3.7V to 14.8V series configurations, with a key caveat: the included wire gauge is fairly small and the holders can be tight to remove individual cells.
California JOS 3 PCS 9V Battery Connector, 9 Volt Buckle Connector Hard Plastic Shell (T-Type)
The California JOS 3 PCS 9V Battery Connector is a practical 9V-specific clip style connector for repairs and DIY STEM projects, with a hard plastic shell and metal terminal for a sturdier feel. Buyers mainly report easy soldering and solid results for replacing broken 9V battery leads, with one notable caveat about corrosion when left exposed outdoors.
2 Pcs Metal Ry-obi 18V Battery Holder/Battery Wall Mount Rack for Ryobi 18V Battery Storage with 3 Slots
These 2-pack metal wall mounts help you store Ryobi 18V slide-style batteries in a cleaner, more organized way. Buyers like the heavy steel build, stable fit for Ryobi One+ batteries, and straightforward mounting, with the main caveat being that you need solid mounting hardware and a good screw fit to avoid small tilting.
2Pcs 18650 Battery Holder Li-ion Battery with Single Compartment, 18650 battery bank & battery backup
A compact 18650 battery holder plus a USB output and micro-USB charging module, sold as 2 sets. It is designed for DIY builds that need simple power management (3V and 5V options) and basic protection features, with a couple of practical tradeoffs around standby drain and guidance.