XSPLENDOR replacement battery for HP iPAQ hx2000 series and rx3000 series
Quick take
This XSPLENDOR battery is a lithium-ion replacement built for multiple HP iPAQ handheld models (including hx2000, hx2100, hx2110, hx2190, and related rx3000/rx3100/rx3400 variants) and a list of specific compatible battery part numbers. It targets the common problem with older PDAs, reduced runtime, but the key buying caveat is strict model and part-number matching.
Pros and cons
Pros
- Designed for a defined set of HP iPAQ models (so it is not a generic battery).
- 3.7V lithium-ion replacement with stated 1400mAh capacity (5.18Wh).
- Buyers report a straightforward “good fit” experience for restoring an older iPAQ.
Cons
- Charging behavior may vary if the battery is not an exact match, based on limited negative feedback.
- Because compatibility depends on part numbers, there is less room for guessing the right battery.
What buyers think
Buyer-review evidence is limited, but the available feedback clusters around two themes. Many reports describe the battery as fitting correctly and performing as expected for older iPAQ devices. A smaller amount of feedback indicates a potential issue with charging fully, which reinforces the importance of matching both your iPAQ model and the specific battery part number.
What this battery replaces, and which devices it fits
This is a replacement battery for HP iPAQ handhelds across several older families, including hx2000 series, hx2100 series, hx2110 and hx2115 series, hx2190 and hx2195, plus multiple rx3000/rx3100/rx3115/rx3400/rx3410/rx3415/rx3417/rx3700/rx3710/rx3715 models. It is also sold as compatible with a set of battery part numbers such as 35H00041-01, 35H00042-00, 360136-001, 360136-002, 364401-001, 367194-001, and 367205-001 (along with additional HSTNH-type part variants listed by the product).
Compatibility tip: before you buy, verify both the device model and the battery part number you are replacing. That is the safest way to avoid mismatches that can show up as charging or performance problems.
Key specs you should know
- Chemistry: lithium-ion
- Voltage: 3.7V
- Capacity: 1400mAh
- Energy rating: 5.18Wh
- Form factor (approx.): 2.47 x 2.19 x 0.21 inches
If your existing battery is a different voltage or significantly different capacity, you may run into compatibility issues even when the physical connector seems similar. Matching the battery part number is the best way to confirm.
Pros and cons for real-world buyers
When this is a good fit
- You have an older HP iPAQ that has reduced runtime and you want a like-for-like replacement.
- Your device is one of the supported models and you can confirm the exact replacement part number.
- You want a straightforward battery swap without changing devices or workflows.
Who should consider looking elsewhere
- You are not sure which battery part number your iPAQ currently uses, and you do not want to verify it before purchasing.
- Your priority is maximum certainty about charging behavior, and you are uncomfortable with limited negative feedback related to charging completeness in a small number of cases.
Installation and expectations
As a replacement battery for a PDA, the main expectation is that it will restore usable runtime after battery degradation. Since lithium-ion batteries can vary with age, storage conditions, and device charge cycles, the most practical approach is to follow a careful compatibility check and ensure your replacement matches the exact part number listed for your model.
Price and availability
Availability is typically listed as in stock with shipping in a few days. For the current price and fastest delivery window, check the live listing:
Bottom line verdict
The XSPLENDOR replacement battery is a solid option if you have a compatible HP iPAQ hx2000 or rx3000-series PDA and you can match the correct battery part number. The main limitation is that accurate compatibility matters, and there is limited evidence of charging issues when a battery is not an exact match. If you are confident in your part-number check, this is a reasonable way to bring an older iPAQ back to daily use.
FAQ
Is this battery compatible with all HP iPAQ models?
No. It is intended for a specific set of HP iPAQ handheld models and a defined list of compatible battery part numbers. Confirm your iPAQ model and the battery part number before ordering.
What are the main technical specs?
It is listed as a 3.7V lithium-ion battery with 1400mAh capacity (5.18Wh). It also has an approximately 2.47 x 2.19 x 0.21 inch form factor.
What if my iPAQ battery charges to less than full?
If charging behavior is incomplete, the most common cause to rule out is compatibility. Double-check that your device model and the battery part number match the supported list for this replacement.
Is it worth buying a replacement battery for an older iPAQ?
If your device powers on but runtime is poor, a replacement battery is often the most direct, cost-sensitive way to extend usability. If you cannot confidently match the part number, however, it can be safer to confirm compatibility first or consider a different replacement approach.
Where can I check the current price?
You can check the latest price and shipping details on the product page here: Buy on Amazon.
Specifications
| Product Title | Replacement Battery for HP iPAQ hx2000 iPAQ hx2100 iPAQ hx2110 iPAQ hx2115 iPAQ hx2190 Part NO 35H00041-01 35H00042-00 360136-001 360136-002 364401-001 367194-001 367205-001 |
|---|---|
| Category | Office Products > Office Electronics > PDAs & Handhelds |
| Brand | XSPLENDOR |
| Manufacturer | Cameron Sino |
| Model Number | CS-RX3000SL |
| Voltage | 3.7 Volts |
| Item Dimensions | 2.47 x 2.19 x 0.21 inches |
| Antenna Location | Laptop |
| Battery Cell Type | Lithium Ion |
| Battery Cell Composition | Lithium Ion |
| Recommended Uses For Product | Laptop |
| Item dimensions L x W x H | 2.47 x 2.19 x 0.21 inches |
Recommended next
PalmOne m105 Handheld
PalmOne m105 is an older Palm OS handheld designed for basic contact, calendar, tasks, and memo capture, with infrared sharing and a backlit display. It can be a good entry point for simple organizer use, but buyers should expect a small screen and a plastic, budget-feel build, and they may run into digitizer or reliability issues with some units.
IYOUBOL Protective Cover Bumper Case Rugged Boot with Hand Strap for Zebra TC51 TC510K TC52 TC56 TC57 (Green)
The IYOUBOL rugged boot case with an integrated stretch hand strap is designed specifically for Zebra TC51, TC510K, TC52, TC56, and TC57 scanners. It focuses on impact protection with raised edges, a non-slip grip edge, and dust-blocking coverage, plus a strap that helps you carry the device more comfortably. The main caveat is that it is not a water-resistant case, so it is best for indoor or protected environments.
Protective Cover Bumper Case Rugged Boot with Hand Strap for Zebra TC51 TC510K TC52 TC56 TC57 (Red)
This rugged bumper-style case with a built-in hand strap is made to fit Zebra TC51/TC510K/TC52/TC56/TC57 barcode scanners, adding anti-slip grip and raised edge protection for daily drops and scuffs. Reviews are mostly positive on fit and durability, with a small amount of limited feedback on material quality.
Digital Digivice 70th Edition WarGreymon G Erosion Mode Classic Color Japanese
The Digital Digivice 70th Edition WarGreymon G (Erosion Mode) is a handheld, battery-powered LCD digivice themed around Digimon. Buyers generally report it arrives in good condition and works as expected, with the main caveat being that the unit is in Japanese and may cost more than other options.