OREI eARC Audio Only HDMI Extender Balun Over Single CAT5e/6/7
Quick take
The OREI eARC-EX165-K extends TV eARC/ARC audio to an AVR or amplifier over a single CAT5e/6/7 cable, designed for long-distance audio return installs. It supports a range of surround and immersive audio formats and is meant to be plug-and-play. The main caveat is power delivery and consistency claims around PoC, so plan for the possibility of powering both units in real-world setups.
Pros and cons
Pros
- Extends HDMI ARC/eARC audio over one CAT5e/6/7 cable (up to 165 ft / 50 m rating).
- Supports common immersive and surround audio formats (PCM 2.0/5.1/7.1, Dolby, DTS family).
- Compact metal housing designed for durability and heat dissipation.
- CEC control support for reducing remote switching.
Cons
- PoC/power-over-cable expectations may not match every install, based on limited reviewer feedback.
- Buyer-review evidence is mixed on long runs and reliability, so proper cable quality and setup still matter.
- Audio-only extension, not a full video HDMI extension, so it will not replace an HDMI cable for picture signals.
What buyers think
Buyer-review evidence shows the OREI eARC-EX165-K can work smoothly for long-distance ARC/eARC audio return when the install matches the intended use case. Positive feedback highlights easy setup (connect sender and receiver, use a CAT5e/6 run, and audio comes through), stable audio without obvious static or delay, and solid build quality with metal enclosures. Some reviewers also mention CEC pass-through working as expected.
On the other hand, evidence is limited and mixed on power delivery behavior (PoC versus powering both ends) and consistency on some shorter CAT6 runs. Because these issues appear in a small number of reports and details like TV model, cable type, and wiring quality are not consistent, buyer-review evidence is not strong enough to guarantee a specific outcome for every setup. Overall, the pattern suggests it is a reasonable audio-return extender choice, but you should be prepared to power both units if PoC does not behave the way you expect.
What this extender is for
This is an audio return channel extender built to carry TV ARC or eARC audio to a receiver or amplifier that is not close to the television. If your goal is to send sound from a living room TV to an AVR in another zone, a media closet, or behind a wall where HDMI cable runs are impractical, a CAT-based eARC/ARC balun like this is designed for that specific job.
Key features that affect buying decisions
ARC/eARC audio extension over a single CAT cable
You run one CAT5e/6/7 cable between the sender and receiver. The product is rated for up to 165 ft (50 m) for eARC/ARC audio transmission, though real-world performance can depend on cable quality, termination, and the overall signal environment.
Audio format support
For home theater buyers, format compatibility matters more than marketing. This model is intended to handle PCM 2.0/5.1/7.1 and surround formats including Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, and DTS-HD Master Audio, plus Dolby Atmos support.
Control and integration
It includes CEC control, which can help you manage receiver behavior without managing multiple remotes or switching inputs manually. Reviewers specifically called out CEC pass-through working well in at least one setup.
Build and installation approach
The housing is metal, which is typically a good sign for long installs where units are left running for hours, and heat dissipation matters. Setup is described as plug-and-play, and multiple reviewers reported it worked immediately with straightforward connections.
Pros and cons, translated into real-world fit
When it’s a strong match
- You only need audio return from TV to AVR (not video).
- Your AVR is farther away than HDMI will reliably reach, and you can run a single CAT5e/6/7 line.
- You want fewer cables and a cleaner long-run install than traditional optical or long HDMI.
- Your TV supports ARC/eARC and your system uses an AVR or amplifier with corresponding HDMI audio support.
When you should think twice
- If you strongly need guaranteed PoC behavior (one end powering the other), note that reviewer experiences are mixed. Plan to use the included power adapters if PoC does not work as expected.
- If your installation environment is noisy (poor cable runs, bad terminations, or questionable CAT cable quality), performance may vary.
- If you need full HDMI extension (video plus audio), this is not the right tool since it is designed for audio return.
Verdict: is the OREI eARC-EX165-K worth it?
The OREI eARC-EX165-K is a practical solution for homeowners and installers who want to extend TV audio return (ARC/eARC) over one CAT5e/6/7 cable to an AVR or amplifier in another room. When the setup aligns with the intended use, buyer feedback suggests it can be straightforward to install and deliver clean audio. The biggest decision point is power behavior and reliability across installs, so if your project depends on PoC working flawlessly, treat that as a “test before final mounting” situation and be ready to power both ends.
FAQs
Does this extender support eARC or just ARC?
It is designed for both eARC and ARC audio return. You connect your TV to the sender unit and the AVR or amplifier to the receiver unit, then run the CAT5e/6/7 cable between them.
Is it audio-only, or does it extend video too?
It is meant for audio return channel extension. It does not function as a full HDMI video extender for picture signals.
What audio formats does it support?
It supports PCM 2.0/5.1/7.1 and a range of surround and immersive formats including Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS, DTS-HD Master Audio, and Dolby Atmos (as supported through ARC/eARC audio return).
Does it work over 50 m / 165 ft?
The extender is rated for up to 165 ft (50 m). Actual results can depend on cable quality, installation practices, and the specific ARC/eARC environment of your TV and AVR.
Does it use PoC (power over cable)?
The product is marketed with PoC. However, reviewer experiences are mixed on whether one end always powers the other. If PoC is critical for your installation, consider planning for the option of powering both units using the included power adapters.
Will CEC work with my receiver?
The extender supports CEC control, and some reviewers report successful CEC pass-through for managing receiver behavior through TV control.
What should I buy this for?
Buy it when you need a cleaner way to send TV ARC/eARC audio to an AVR or amplifier that is too far for a straightforward HDMI run, and you are comfortable using a single CAT5e/6/7 cable for the link.
Specifications
| Product Title | OREI eARC Audio Only HDMI Extender Balun Over Single CAT5e/6/7 ARC Audio Return Channels Through HDMI Up to 165 Ft - PoC, CEC Control |
|---|---|
| Category | Electronics > Television & Video > AV Receivers & Amplifiers |
| Brand | OREI |
| Manufacturer | OREI LLC |
| Model Number | EARC-EX165-K |
| Color | black |
| Connector Type Used on Cable | HDMI |
| Compatible Devices | Television, AV Receiver, Amplifier |
| Cable Type | HDMI |
| Number of Ports | 1 |
| Power Source | AC adapter |
| Audio Output Mode | Stereo, Surround Sound, Immersive Audio |
| Item Dimensions D x W x H | 2.5"D x 2.5"W x 1"H |
| UPC | 810162900762 |
| Mfr Part Number | eARC-EX165-K |
| Warranty Description | 1 Year Warranty |
| Connector Type | HDMI |
Recommended next
Pyle 500W Karaoke Amplifier with Bluetooth (PTA44BT.5)
A budget-friendly, multi-input karaoke amplifier with Bluetooth streaming, front mic inputs, and adjustable EQ for bass, treble, echo, and talk-over. Best for home or casual commercial karaoke use where you want flexible inputs and simple controls, with the main caveat being that the real-world “500W max” output depends heavily on speaker choice and setup.
TTQ Wireless HDMI Transmitter and Receiver (TR60-Green)
The TTQ Wireless HDMI Transmitter and Receiver (TR60-Green) is a plug-and-play wireless HDMI extender for mirroring from a compatible laptop/PC or camera/DV setup to a TV, monitor, or projector. It supports 4K decoding while outputting 1080P at up to 60Hz, uses dual-band 2.4G/5G for up to about 100 ft, and includes an LED display for signal/power status. The main tradeoff to consider is that it is designed for HDMI sources, not smartphones/iPads, and it is not ideal for very low-latency gaming.
2027 Upgrade Wireless HDMI Transmitter and Receiver 400FT/120M, LDS Antenna review
This BRAIDOL wireless HDMI kit is built for simple, Wi‑Fi-free setup, long-range placement, and 4K decoding with 10‑bit color for presentations, streaming, and on-the-go meetings. The biggest buying caveat is that “wireless HDMI” performance still depends on power, line of sight, and your environment, so you will want to plan placement and keep both units powered.
Elalight Wireless HDMI Transmitter and Receiver 328FT/100M (2.4G+5G) Plug & Play Kit
The Elalight Wireless HDMI transmitter and receiver kit is built for simple cord-free screen sharing between a laptop and a TV, projector, or monitor. It supports 4K decoding with 1080P/60Hz output, offers mirroring and extension modes, and is designed for long-range use with a 2.4G/5G dual-band wireless connection. The main caveat is buyer-fit: it is not recommended for gaming, and a small set of users report reliability issues over time.